Which VHF Channels Should You Use in Australia?
Channel 16 is the international calling and distress channel. Call on 16, then move to a working channel so 16 stays clear for emergencies. In Australia, channel 67 is also a safety channel, channel 70 carries digital DSC messages only, and the repeater channels are 21, 22, 80, 81 and 82. Repeaters work in duplex mode, so set your radio to international mode when you take it out of the box. In US mode those channels are simplex and you won't hear the reply.

Video, 10:39. Captions are available in the player.
In this lesson
In this lesson I explain how VHF channels relate to frequencies, the difference between simplex and duplex channels, how repeater stations extend your range, the 30-second repeater timeout, and the channels every skipper should know: 6, 13, 16, 67 and 70.
- 0:00VHF frequencies and channels
- 1:12Why channel 60 sits next to channel 3
- 2:13Every channel has a purpose
- 2:43Simplex channels
- 3:46Duplex channels
- 4:50Repeater stations
- 6:24Australian repeater channels
- 7:26The 30-second timeout
- 7:57Set your radio to international mode
- 8:58Channel 16 and channel 67
- 9:31Channel 70 and DSC
- 10:02Channels 6 and 13
Read the transcript
We've already learned that radio messages are transmitted by electromagnetic waves, and that these waves have different frequencies and wavelengths. The higher the frequency, the shorter the wavelength. And you need to know, because it is usually in the exam, that VHF operates within the 30 to 300 megahertz range. In fact, marine radios operate on only a small proportion of that range, between 156.0 and 162.025 MHz. But you rarely hear anyone refer to specific frequencies in VHF.
Instead, we speak about channels. For example, 156.8 MHz is the international calling and distress channel, but it's always referred to as channel 16. You might think that the higher the frequency, the higher the channel when it comes to VHF, but here's a fun fact for you. Initially, there were just 28 channels across the entire spectrum from 156.0 to 162.025 MHz. But as VHF became more and more popular, these channels became crowded and people would be forever talking over the top of each other.
But there was plenty of space between the channels across that spectrum, and so channels 60 to 87 were added in between channels 1 to 28. This means that the frequency of channel 60 is just above channel 3, and channel 28 is higher than channel 87. Notice also that there's nothing between 28 and 60. Have a look at the channels on your set and you'll see that it goes 28 and then straight to 60. In order to reduce disruption, especially on emergency and important port operation channels, each channel has been given a designated purpose.
You'll be given the opportunity to review these later in this lesson, and you can download a complete and detailed chart in the lesson resources. A slightly confusing feature of marine radio is the distinction between simplex and duplex channels. But don't worry, this is something you need to be aware of, but not an expert in. Simplex is straightforward. That's why it's called simplex.
You will need to know the definition of simplex for the exam. Simplex mode is where you have the same frequency for transmitting and for receiving. The limitation of simplex communication is that only one message can travel on the frequency at any one time, so only one person can talk at once. That means the person listening needs to wait until the speaker has finished before transmitting. They can't interrupt or talk over them, and so that natural form of communication back and forth is lost.
So we have procedures such as saying "over" at the end of the transmission to ensure we don't miss each other. Because of this limitation, some boffins came up with the idea of duplex channels. A duplex channel pairs two frequencies, one for transmitting and the other for receiving. In duplex mode, the ship transmits on channel A and the shore listens on channel A. The shore transmits on channel B and the ship listens on channel B.
That way, both lines can remain constantly open and a regular conversation can happen. The duplex system was initially developed for ship-to-shore communications in the UK, and made radio communication on those channels just like speaking on the telephone. It even allowed ships to be connected into the land-based telephone network. The development of mobile phones meant that this system is largely defunct in the UK, because they have much better mobile phone coverage, but it still has special significance in Australia because of repeater stations.
Because VHF communications depend on the height of antennas, the use of repeater stations can significantly increase coverage. These repeaters are shore-based installations that are found at regular intervals on high points along the coast and in some inland locations. A repeater receives a signal and retransmits it, usually with higher power and from a better location, to provide a greater communication range. But here's the thing. In Australia, repeaters operate in duplex mode, not simplex.
And if your radio is set up correctly in international mode, then when you turn to a repeater's channel, your transceiver will automatically operate in duplex mode. That is, the repeater receives your transmission on frequency A and retransmits your signal on the paired frequency B. When you want to speak to another station through a repeater, you need to know the channel of your nearest repeater, usually from information you'll find online. The receiving station will also need to be on that channel.
In Australia, and you may well need to know this for the exam, the repeater channels are 21, 22, 80, 81 and 82. That's 21, 22, 80, 81 and 82. Say, for example, boats on Port Phillip will use the repeater on Arthurs Seat, which is on channel 82. Say you want to contact a station in Western Port or out to sea where you've no direct line of sight. Well, you'll both need to have pre-arranged to monitor channel 82.
In the UK, the use of repeaters for ship-to-ship communications is frowned upon, so RYA courses and books insist that they're strictly ship to shore. But in Australia, repeaters can be used for any communications. But these channels shouldn't be used for extended conversations, and to make sure you don't, Australian repeaters have a 30-second timeout. This means that after 30 seconds of continual transmission, they automatically switch off for a couple of seconds. They can be reactivated by momentarily releasing the PTT key on your radio and then transmitting again.
This is designed to stop people overusing the channel, because it can be used in emergency situations. Another thing to note is that the US and Canada use our duplex repeater channels 21, 22, 80, 81 and 82, but in simplex mode. That's why it's so important that you set your radio to international when you take it out of the box. It's not unusual in the Sydney to Hobart for a yacht at the bottom of the Derwent to transmit on 81 but not hear the reply, because they're set to simplex mode and they don't hear the reply on the duplex channel.
Well, for the rest of this lesson, you're going to review a chart of the different channels, their frequencies and their uses. It is important that channels are used only for the purpose for which they have been assigned. For example, channels authorised for calling are not used as working channels. Channels authorised for calling coast stations are not used for calling ship stations, and so on. The most important channel is channel 16, which has a dual purpose.
It is a calling channel, as you contact the coastal patrol or the port authority or another vessel on 16, but then you will switch to an appropriate working channel, which is where the conversation can be carried out. The reason we move away from 16 once communications have been established is so others can call. Most importantly, because it is the distress and safety channel, we want to keep it open for emergencies. In Australia and in the UK, channel 67 is also used in addition to 16 as a safety channel.
You'll also note that channel 70 is a bit odd. That's because it's not used for voice messages, but for digital, or DSC, messages that we'll discuss in a later lesson. A couple of channels you should be especially aware of are channel 6, which is used for ship-to-aircraft messages in search and rescue operations, and channel 13, for ship-to-ship safety information. Well, now's the time for you to review the marine radio channel allocations table and answer a few questions to help you know what each of those channels is for.
More on marine radio
- How Do You Say Letters and Numbers on a Marine Radio?
- How Do You Make a PAN PAN or SECURITE Call?
- What Are DSC and an MMSI on a Marine Radio?
- What Is AIS, and How Does It Work on a Boat?
- How Do HF Radio Signals Travel? The Ionosphere Explained
- What Are the HF Marine Radio Distress and Calling Frequencies?
This lesson comes from our VHF and MF/HF marine radio courses at Marine Radio Online, which prepare you for the SROCP and LROCP marine radio operator exams.
