How Do HF Radio Signals Travel? The Ionosphere Explained
HF signals travel long distances by bouncing off the ionosphere, a layered band of the atmosphere 50 to 400 kilometres up that is energised by the sun. By day the low D layer absorbs lower frequencies, so you use higher ones, typically 10 to 16 MHz. At night the D layer disappears and you drop to roughly 2 to 10 MHz. Go too high and your signal passes straight through the ionosphere, so if you get no response, try a lower frequency.

Video, 11:03. Captions are available in the player.
In this lesson
In this lesson I explain how the ionosphere forms, its D, E, F1 and F2 layers, the maximum and lowest usable frequencies, and how the solar cycle, latitude and season change what works, with a look at the Bureau of Meteorology's ionospheric maps.
- 0:00How HF signals travel
- 1:11What you need for the exam
- 2:47What is the ionosphere?
- 4:20The ionosphere's layers by day
- 5:53Maximum and lowest usable frequency
- 6:23The ionosphere at night
- 6:53The solar cycle
- 7:23Latitude and the equatorial anomaly
- 8:23Seasons and the Bureau of Meteorology map
- 9:25Watching the ionosphere change over a day
Read the transcript
HF propagation, that is, how the signals are transmitted across the earth, is a very complex topic, but also pretty amazing. HF signals bounce off the ionosphere. But because the behaviour of the ionosphere varies so much between daytime and night-time, from season to season, across different latitudes and across the 11-year solar cycle, you need to understand the theory of propagation if you're going to make HF transmissions that bounce off the ionosphere back to earth and are received, rather than being either absorbed by it or going right through it.
Now, if all you want to do is pass the exam, there are just a few things you need to know at this point. But if you want to actually use a transceiver, this lesson provides a vital introduction to the theory and some resources to take you further. So, here's the information you need to pass the exam. Firstly, during the daytime lower frequencies are not reflected but absorbed, and so during the daytime higher frequencies should be used than at night. These might be in the 12 and 16 megahertz bands.
If your frequency is too high, however, it's not going to be reflected either, but will go right through the ionosphere. So, if you get no response, lower your frequency. Then you need to know the distress frequencies for MF and HF. They are 2182, 4125, 6215, 8291, 12290 and 16420. The calling frequencies are slightly different: 2182 again, but then 12359 and 16537.
But as I say, if you're actually going to use an HF unit, you need to understand the theory behind propagation. That is vital to being able to make successful HF transmissions. In order to understand propagation, we've got to understand the ionosphere. As we've heard, the reason HF signals can travel so far is that their sky waves bounce off the ionosphere. The ionosphere is a band of the atmosphere that sits 50 to 400 kilometres above the earth, but far from being a single band of matter that reflects things, it is complex, multi-layered and ever-changing.
The ionosphere itself is created when UV radiation from the sun hits hydrogen and helium atoms in the atmosphere. It is the collision of UV radiation with these atoms that displaces a negatively charged electron from within the atom. The electron flies off and, unleashed from its atom, is called a free electron. It leaves behind an atom that's missing an electron, and these are called ions. But it's the free electrons that get hit by the radio wave that you have transmitted.
Your signal causes the electron to vibrate at the frequency of your radio signal, and it's that vibration of the free electron that relays and bends the signal so that it's heard back on earth, well over the horizon. The density of these electrons varies greatly at different altitudes, and so does the amount of energy hitting these atoms, and so four distinct regions of the ionosphere are formed during the day. These layers are distinctive, and radio waves interact differently with each. They're labelled D, E, F1 and F2.
The ionosphere needs radiation from the sun, so it looks very different at night and behaves very differently too, and that means your transmissions behave differently by day and by night. During the day, the lowest layer, the D layer, is active, and its properties mean that it absorbs frequencies in the lower range, under 10 megahertz. But the F2, the top layer, is also active, and the free electrons there are vibrating at a high frequency, relaying and bending higher frequency radio waves. This means that during the daytime we use higher frequencies, typically between 10 and 16 megahertz.
But while we'll get the best results by going as high as possible, we also get to a point where we're going too high. These free electrons will grab hold of and relay any frequency that is the same as or lower than the frequency they're vibrating at due to the energy of the sun. If the free electron is vibrating at 16 megahertz, it will propagate any transmission at 16 megahertz or lower. But a transmission at 22 megahertz is simply going too fast for it to grab, and so the transmission goes right through and is lost in space.
That means that the more active the ionosphere, the higher the frequency you can operate on. The highest frequency at which you can operate is called the maximum usable frequency, or MUF. The lowest frequency you can operate on without the electromagnetic wave being absorbed by the D layer is the lowest usable frequency, or LUF. At night, the D layer disappears entirely. F1 and F2 combine, leaving just two layers with far less energy than during the daytime.
With the F layer less energised, the free electrons are vibrating at a lower frequency, and so the MUF is much lower. But that's okay, because the D layer that absorbs lower frequencies has disappeared, and so your LUF is lower too. So you get the idea that we use higher frequencies during the day and lower frequencies at night. As a rule of thumb, these should be between 2 and 10 megahertz at night and 10 and 30 by day, though we seldom go above 18.
There are other factors that affect the MUF and the LUF. Solar flares significantly increase UV radiation, and therefore the energy and activity of the ionosphere. The level of solar flare activity increases and decreases over an 11-year cycle. 2020 was the last low point, meaning that up until 2026 we see increased activity: we're able to use higher frequencies and therefore achieve a longer range. Then, beyond 2026, the level of activity diminishes again.
The MUF also varies considerably with your latitude. Now, you'd expect the most activity at the equator, where it's hottest, and the least at the poles, which is generally the case, but there are aberrations at each end. The equatorial anomaly means that the peak is not at the equator, but 15 to 20 degrees north and south. Also, at night the MUF drops to its lowest not at the poles but at 60 degrees latitude. There are also seasonal variations, but these are not as pronounced as the solar cycle and latitude effects, and they're quite complicated, so we'll give them a miss, except to say that the equinoxes in March and September are associated with higher daytime frequencies than other times of the year.
An interesting reference is the ionospheric map produced by the Australian Bureau of Meteorology. It shows the frequency of the F2 layer throughout the world, and can be animated to show how it has shifted over the last couple of days. You'll notice how the highest frequency moves west with the sun, and you can also see the equatorial anomaly, with the highest frequencies not on the equator but around 20 degrees either side. The Bureau's site also has warnings of fade-outs and other atmospheric disturbances, to help you find the right frequency for the conditions.
Another feature is a live display of the current ionosphere for different parts of Australia. It allows you to clearly see the differing layers, and by time-shifting you can see how they change through the night and day. The colours within these bands show the electron density, with red being the most dense. As we run through a 24-hour period, you can see the D layer, and from that determine the LUF, which is about 3.8 megahertz here, and the MUF, which is a little lower than we might expect at 9 megahertz.
During the night hours, the D region is empty and the E and F layers dominate. As dawn breaks, energy builds along with the activity in the D region, and the F layer becomes higher in frequency, and you start to see the F2 layer emerge at the top of the screen. Well, that's my introduction to the ionosphere. It's a lot to take in, but if you get the basic concepts, you are well on your way to knowing how to make transmissions that are heard. And if they're not, you'll have an idea of what you need to do to make sure your signals bounce off the ionosphere.
More on marine radio
This lesson comes from our VHF and MF/HF marine radio courses at Marine Radio Online, which prepare you for the SROCP and LROCP marine radio operator exams.
