Resources › Coastal navigation
How Do You Read a Nautical Chart? Symbols and Depths
The depths on a chart are soundings at chart datum, which in Australia is usually lowest astronomical tide (LAT): the lowest level the tide is predicted to reach under normal conditions. So the water is seldom shallower than the chart shows, but strong winds or high pressure can push it below LAT. Add the height of tide to the charted depth to get the actual depth. A drying height, often underlined in the green area of the chart, is how far the bottom stands above chart datum.

Video, 11:30. Captions are available in the player.
In this lesson
In this lesson I show how to use a Portland plotter to measure and plot a bearing, how to read chart symbols with the INT 1 reference, how to read soundings, contour lines and the colours that warn of shallow water, and how to work out clearance under bridges and power lines.
- 0:00Using a Portland plotter
- 1:36Plotting a bearing
- 3:20Chart symbols and INT 1
- 4:53Soundings and chart datum
- 5:18Lowest astronomical tide
- 6:24When the water drops below chart datum
- 7:00Spot soundings and contour lines
- 7:47What the colours mean
- 8:44Drying heights
- 9:26Clearance under bridges and power lines
- 10:41Summary
Read the transcript
In module one, we learnt how to use dividers to measure distance. There's another important instrument that makes up your navigation toolbox, and that's a plotter. There are a number of tools that you can use to measure headings and bearings. In my view, the easiest to use and most accurate is the Portland plotter. A Portland plotter is a rectangular transparent tool with a rotating compass rose and grid lines.
I'll show you how to use it. Let's say we have plotted a course on the chart and want to determine its heading. Place the edge of your plotter along your line. Notice that having a pencil at one of the points makes this easier. Make sure the large blue triangle is pointing in the direction you're wanting to go.
Now rotate the dial until the grid lines on the dial align with the chart's meridians, the north south lines, sliding the plotter along the line if you need to so that you can accurately align the grid on the plotter with the grid on your chart. Also, ensure the n on the dial is pointing towards the top of the chart. Then it's just a matter of reading the bearing at the arrow. That's your bearing in degrees true. That's how we measure a heading.
We could also plot a bearing. That is work backwards. Let's say you determine that a lighthouse is a particular bearing, say 120 degrees true. Set the desired bearing so that it is on the arrow at the zero on the plotter's dial. Place the plotter at the target, ensuring that the big blue arrow is pointing in the direction of the target.
Now rotate the whole plotter until the grid lines align with the charts meridians with north pointing up. Now just draw a line along the edge. You'll practice this for yourself in a moment. I want you to notice that right now we're working in true bearings. That's bearings relative to true north as shown on the chart.
In module three, we'll learn how to convert these to magnetic and compass bearings, which you'll actually steer by. For now, always note that your bearings are true by writing the t after them. Well, once again, when pause comes up on the screen, you should pause the video and follow the on screen steps to plot a course. Once that's done, push play, check your answer, and then you'll get another chance to push pause, and that time measure a heading. Every chart is filled with symbols, wrecks, rocks, buoys, lights, beacons, cables, restricted areas, and dozens of other features.
These symbols are standardised internationally in a reference called INT one, the International Hydrographic Organization chart symbol dictionary. Australian charts also include some local variations. You don't need to memorise every symbol. There are hundreds, but you must know how to look them up, and you'll quickly learn the most common ones through regular use. When you encounter an unfamiliar symbol, don't guess, look it up.
On this chart of Pittwater, I can see a lighthouse with Fl(4) 20s. We'll learn what that means in a later module. Here's a rock with a one metre drying height, shallow water here at the mouth of Pittwater that will need to be navigated with care, a seaplane landing area that requires special caution, and numerous submerged cables where we can't anchor. In a moment, pause the video to complete the exercise that will come up on the screen using your Hypothetical Bay chart. Understanding depth information is critical for safe navigation.
The numbers scattered across a chart are soundings, depth measurements, but the water's depth is never constant. Tides, in particular, change the depth. So what does it mean that somewhere is 10 metres deep? When is it 10 metres deep? The depth information on charts gives you the depth of the water at chart datum.
In Australia, chart datum is typically lowest astronomical tide, abbreviated LAT. That's the lowest level the tide is predicted to reach under normal astronomical conditions. That is based on the effects of sun and moon, excluding extreme weather effects like cyclones. Chart datum is the reference level from which all depths and drying heights are measured. LAT is a conservative baseline.
It means the water is seldom shallower than the depth shown on the chart. In practice, you'll usually have more water than the chart indicates even at low tide. But, and this is important, don't count on it. Meteorological effects like strong winds or high atmospheric pressure can push waters below LAT. I was preparing to cross the bar at Bermagui on the south Coast of New south Wales and was surprised to see the low tide prediction was actually minus 0.2 metres.
It was below chart datum. As a datum point, the chart datum is the baseline from which tidal information is interpreted. We'll cover tides in a later module, but if high tide is 2.2 metres, that means the depth will be 2.2 metres greater than chart datum. So a point shown as 10 metres on the chart will be 12.2 metres when the tide is at 2.2 metres. Charts show depth in two ways.
There are spot soundings, that's individual numbers scattered across the chart showing the depth at that specific point. On modern Australian charts, these are in metres. Always check the depth units note on the chart as older charts might use fathoms. Then there are contour lines, lines connecting points of equal depth similar to elevation contours on a land map. Common contours include five, 10, 20, 50 metres, and they help you visualise the underwater terrain, where it's shallow, how quickly it drops off, and where channels run.
Charts use colour to emphasise depth information and in particular to warn you of shallow water. Shades of blue to show shallow water, typically different shades for zero to two metres, two to five metres, and a little lighter for five to 10 metres. Blue means pay attention. This is shallow water. The darker the blue, the shallower the water.
White indicates deeper, safer water. Then you'll see green shading. These are drying areas, zones that are underwater at high tide, but exposed at low tide. These waters can appear deep when you look at them at high tide, but are dangerous if you cross them at the wrong state of the tide or with a deep draft vessel. A drying height is shown as a number inside the green area often underlined.
For example, 0.5 means this area stands 0.5 metres above chart datum at low water. At high tide, it might be covered by two or three metres of water. At low tide, it's a sandbank or rocky outcrop. Just as depths are measured downward from LAT, lowest astronomical tide, heights on land are measured upward from highest astronomical tide. That is the highest level the tide is predicted to reach under normal astronomical conditions.
This is critical for calculating clearance under bridges, power lines, or overhead obstructions. If a chart shows a bridge with a vertical clearance 15 metres h a t, it means you have at least 15 metres of clearance even at highest predicted tide. Your boat's air draft, that's the height from the waterline to your highest point, usually the masthead, must be less than this clearance. But always add a safety margin. If your mast is 14.5 metres and the bridge clearance is 15 metres, you're cutting it far too fine.
Wait till the tide drops. Wave, swell, and tide measurement uncertainties could put you in contact with that bridge. So we need to add a margin of safety and cross when we achieve that margin. In a moment, it'll be time to pause the video and take out the chart you've purchased for this course if you've done so. Follow the on screen instructions to crack the code and identify the key features on your chart.
Before you move on to module three, complete the practice exercises that follow. Make sure you're comfortable using the Portland plotter and dividers. These are hands on skills that get easier and fastest with practice, so practice is essential. And do the quiz to see how you're going with your learning. In module three, we'll turn our attention to the compass and learn how to account for magnetic variation and compass deviation.
The corrections needed to convert between the true bearings that you plot on a chart and the magnetic and compass headings you actually steer by. See you in the next one.
More on coastal navigation
This lesson comes from the Australian Coastal Navigation Course, based on The Australian Coastal Navigation Handbook, and supports our practical coastal skipper courses.
