Resources › Boat licence and powerboat handling
How Do You Drive and Anchor a Powerboat?
At low speed a powerboat only steers when it has thrust, so use "steer, then gear": turn the wheel first, then give a short burst of power and go back to neutral. To get on the plane, trim down, check around you and increase throttle smoothly, then trim up once you're planing. When anchoring, keep out of channels and no-anchor zones, and let out about four times the depth if you have all chain, or six times with chain and rope.

Video, 9:17. Captions are available in the player.
In this lesson
In this lesson I cover low-speed handling and holding position in wind, getting on the plane, turning and slowing down safely, trim, and how to set and retrieve an anchor.
- 0:00Displacement and planing
- 0:43Low-speed handling: steer, then gear
- 1:44Holding position in wind
- 2:45Practise slow-speed handling
- 3:10Getting on the plane
- 4:30Turning at speed
- 5:20Slowing down safely
- 5:40Trim
- 6:30Where to anchor
- 7:10How much anchor line?
- 8:05Setting and retrieving the anchor
Read the transcript
There are really just two modes for a powerboat: slow speed and high speed. When you're travelling at low speed, the boat is in displacement mode, which means it sits in the water. When you're travelling at high speed, it's in planing mode, with the boat sitting on the water. These two modes have very different characteristics and require a different style of boat handling. Let's start with slow speed boat handling.
Powerboats are actually quite difficult to control at low speeds, like when you're approaching a jetty or a trailer. The boat will only steer when you've got thrust, but when you apply thrust, the boat accelerates and goes faster than you may want. So the trick here is to use intermittent thrust. That is, steer the boat in the direction you want to go, give a short, small burst of thrust and then go back into neutral. Just proceed slowly, with plenty of time in neutral and little bursts of thrust, making sure you've turned the wheel before engaging gear. It's called "steer, then gear": turn the wheel before you engage power.
Holding position is also a challenge, especially when it's windy or there's a strong tidal current. Say you're standing off a boat ramp and want to stay in place. Two things happen. The whole boat is pushed downwind, and the bow is pushed further downwind than the stern, until the boat is lying stern to the wind. When this happens, it's sometimes easiest just to hold position stern to the wind, with intermittent thrust to keep you where you want to be. This works particularly well when the waves aren't large.
But when you need to keep the bow into the wind, the steer-then-gear technique with small pulses of the motor will keep the bow into the wind. The way the wind affects a boat varies greatly from boat to boat: it's influenced by its weight, shape and size. So if you're new to boating, or have a new boat, it's a good idea to practise slow speed boat handling. Drive figure eights around a couple of markers, or if it's windy, practise holding position a couple of metres off a timber buoy. We use timbers so that if we touch one, we won't damage the boat.
Getting the boat onto the plane is when your boat transitions from displacement mode to planing mode, where it skims across the surface, significantly increasing speed and efficiency. Check your surroundings before you pick up speed, and make sure everyone is hanging on and knows what you're about to do. If your boat has trim tabs or engine trim, something we'll talk about more in a little while, then lower them all the way down. This will help ensure that the bow stays down and the boat gets on the plane more easily. If you don't have trim tabs, you may need to get the crew weight forward until you're up on the plane.
Gradually increase the throttle. Don't slam it forward; increase power smoothly and steadily. Feel the boat. You'll notice the bow begin to rise as the boat accelerates, and as the bow rises your visibility may be temporarily reduced, so make sure you've got a clear view of your surroundings. Steer straight ahead and apply more throttle. As the boat gains speed, start to gradually trim the tabs up. Then find the sweet spot between trim and speed, making sure you're travelling at a safe speed once you're on the plane. The less power your boat has, the more difficult this process is and the longer it will take.
If you need to make a turn, start by reducing your speed and ease into the manoeuvre. Avoid sharp turns at high speed, as they can lead to loss of control or even flip the boat. At high speeds, even small adjustments can have significant effects, so be smooth with your movements. Tight turns at speed are to be avoided because the stern may skid out and catch a wave, ejecting the crew or flipping the boat, and the increased g-forces of a fast, tight turn increase the chances of someone going overboard.
Any reduction in speed should also be steady and controlled. As you slow down, the stern wave may catch up with you and even swamp the boat, so be aware of what is happening behind you and slow down in a staged, gradual way. Trim is important for optimising performance on the plane, getting the right angle of attack to the waves, and ensuring good balance. If your boat doesn't have trim tabs, you can adjust its trim with the engine or leg tilt.
As you start to move from displacement to planing mode, you want the engine or leg trimmed in to keep the bow down. Once on the plane, ease the leg out, or slightly raise the engine, to get the boat into the sweet spot. If you have tabs, keep them down as you start and bring them up as you come onto the plane. Trim needs frequent adjustment as speed varies, as conditions change, or as your crew moves around the boat.
Anchoring is as much a part of boating as motoring along. Not only is it an opportunity to fish or swim, but it is an important course of action in an emergency. Make sure you don't anchor in a channel or fairway, or in a no-anchoring zone. You'll be safest and most comfortable out of the waves and wind, and you'll need to make sure you leave enough room so you don't swing into other boats that are already anchored there.
The big question when anchoring is how much line to put out. An anchor will only hold if it stays flat on the sea floor. It is the chain that weighs down the shank and keeps the anchor flat and in the sand. So if your anchor has just chain, in most conditions put out four times the depth. That ratio of four to one is called the scope. If you have a mix of chain and rope, then make it six metres of line for each metre of depth. A scope of six to one is also a good ratio in strong winds.
Ideally you'll anchor in sand, or if you have to, in mud. Weed doesn't provide any holding and must be avoided. And don't anchor on reef unless you have a reef pick, otherwise you'll struggle to retrieve your anchor. Reef picks are designed to straighten out so they can be retrieved from a reef. Have your crew lower the anchor, and as it touches the seabed, apply a little reverse so the chain is laid out along the sea floor.
Once the required amount of chain has been paid out, secure the line to the boat and apply reverse briefly to set the anchor, so it digs into the sand. You can apply a bit more reverse thrust to check that it's holding properly. Line up two objects on the land, or use your GPS: if the two objects on land stay in line, you're set. When you're ready to pick up the anchor, it helps to motor forward a metre, then have the crew raise the line, move forward another metre, raise the line, and so on. If you don't have a windlass, that makes it much easier on the crew.
More on boat licence and powerboat handling
This lesson comes from our Victorian boat licence course at vicboatlicence.com.au, run with Go Workplace Training (RTO 22464).
